|
Product
Information—For Immediate Release
FAIRLANE PRODUCTS INTRODUCES A FULL RANGE OF WIRE ROPE LANYARD ASSEMBLIES
Fairlane Products, Inc.(Fraser, MI) has announced introduction of a full range of
wire rope lanyard assemblies. These wire rope lanyard assemblies are used to attach
quick release pins to a fixture or frame, to prevent the pins from being misplaced
while they are not in use.
All of the wire rope lanyard assemblies are made from 7 x 7 stainless steel wire
and are available either uncovered (bare cable) or covered. The vinyl covered
assemblies are available in either clear, black or green. The 3/64" wire is
covered to 1/16" diameter. The 1/16" wire is covered to 1/8" diameter.
They are available with three different tab styles including rectangular, teardrop,
eyelet. The tabs allow the user to connect the cable assemble to a frame or
fixture so it does not become separated. A lanyard with loops on both ends is also
available. The standard lengths of all assemblies are 6", 8", 10" and 12".
The rated break strength of the 3/64" wire is 270 pounds, and the 1/16" wire
is 480 pounds. Cable assemblies using eyelets are rated at 30 pounds. All tabs
and eyelets are manufactured from 300 series stainless steel. All cable sleeves
are manufactured from zinc plated copper.
In addition to the standard parts, we can provide custom lanyards based on your
exact requirements.
To see our entire line of our wire rope lanyard assemblies, please visit
www.fixtureworks.net.
Back
to top ^
|
 |
|
Product
Information—For Immediate Release
FAIRLANE PRODUCTS CREATES A LINE OF RECEPTACLES FOR USE WITH THEIR QUICK RELEASE BALL LOCK PINS
Fairlane Products, Inc.(Fraser, MI) has announced creation of a line of receptacles
for use with their quick release ball lock pins.
These flanged receptacles provide a permanent and proper mating hole for quick release
ball lock pins. They are designed for use on materials and in applications where the
pin does not have anything to lock against.
Because the pin does not protrude out the bottom of the receptacles, they are ideal
for blind-hole applications. The receptacles can be mounted with screws, rivets or
bolts. They are made from 303 stainless steel.
In addition to the flanged receptacles, we are offering a new line of end caps that
fit over the end of the quick release ball lock pin and allow the pins to be used in
applications where the receiving hole is not within tolerance or is out of round.
These receiver caps can replace cotter pins and hitch pins to allow you to take
advantage of quick changing and fieldwork without tools. The caps are made from 303
stainless steel.
To see our entire line of our wire rope lanyard assemblies, please visit
www.fixtureworks.net.
Back
to top ^
|
 |
|
Product
Information—For Immediate Release
FAIRLANE PRODUCTS CREATES A FULL RANGE OF QUICK RELEASE BALL LOCK PINS
Fairlane Products, Inc.(Fraser, MI) has announced creation of full range of
quick release ball lock pins.These quick release pins have a wide range of
applications in fastening, locating, and alignment applications. The pins will
not release until the button on the handle is depressed offering secure and
safe fastening. Once the button is depressed, the balls retract into the pin
allowing the pin to be inserted or removed into or out of a hole.
Because they are positive locking, they can replace traditional fasteners such
as nut and bolts, cotter pins, hitch pins, etc. They also allow the user to
insert and remove the pins without the use of tools making them ideal for field
work and quick change operations.
These pins are available in three shank materials to meet a wide range of
application needs.
17-4 SS - Made from heat treated 17-4 stainless steel, they are designed for
applications where higher shear strengths are required. Because they are made
from stainless steel, they offer superior corrosion resistance over alloy steel.
This combination of strength and corrosion resistance makes it a good choice for
a wide range of demanding applications.
304 SS - Made from non-hardened 304 stainless steel, these pins are not designed
to be used where shear strengths are demanding. While these pins offer lower
shear strengths than other materials, they are strong enough to meet the needs
for many applications. This material also offers very good corrosion resistance.
4130 Alloy Steel - Made from heat treated and plated 4130 alloy steel, these pins
are ideal where high strength is required and environmental factors are not an issue.
There are four standard handle styles. Our standard handles are made from aluminum
alloy and are anodized black. They are available in Ring, Button, T and L configurations.
Handle choice is based on clearance, use and appearance. The Ring and Button handles
are also available in stainless steel.
To see the entire line of our quick release ball lock pins, please visit
www.fixtureworks.net.
Back
to top ^
|
 |
Product
Information—For Immediate Release
FAIRLANE PRODUCTS INTRODUCES LINE OF SQUARE,
RECTANGULAR AND SPECIAL CUT BUMPERS
Fairlane Products, Inc. (Fraser, MI) has announced the introduction of
square, rectangular and special cut bumpers to complement its existing
line of round bumpers. These bumpers are available in “off-the-shelf”
sizes, as well as special cut to custom requirements. The square and rectangular
bumpers are available in black neoprene and polyurethane in 60 and 80
durometers with sizes of ¾-inch square to 2½-inch x 4-inch.
Heights from 3/8 to 2-inch. Special cut bumpers are available in black
neoprene, 80 durometer, with thickness from 3/8 to 2-inch. All special
cut bumpers can be fabricated with drilled, counter-bored or tapped holes,
with aluminum backing.
Fairlane Products is a leading designer and manufacturer of rollers and
bumpers used in materials handling, assembly and manufacturing applications.
The company also designs and manufactures a wide range of workholding
and positioning components and thrust screws, all built to promote higher
productivity through faster speeds and feeds — while their modular
and economical replaceable wear surface extends the life of expensive
jigs, fixtures, jaws and clamping mechanisms. In addition, the company
designs and manufactures serrated grippers, encompassing hardened high-speed
tool steel or solid carbide diamond pattern grippers, low-profile edge
grippers, single point and straight serration grippers.
Other products include
Swivots® — modular component workholding elements incorporating
a serrated gripper, smooth pad, or a Delrin® rest pad that rotates
and pivots for holding and positioning of irregular contour surfaces.
Send inquiries to:
Fairlane Products, Inc.,
33792 Doreka, Fraser, MI 48026.
Tel: 586.294.6100
Fax: 586.294.6822
Online: www.fairlaneproducts.com
Back
to top ^ |
|
Product
Information—For Immediate Release
FAIRLANE PRODUCTS INTRODUCES LINE OF EXTENDED
SHAFT DRIVE ROLLERS
Fairlane Products, Inc. (Fraser, MI) has introduced a new line of extended
shaft-drive rollers—rollers that lock onto a shaft to motorize,
convey and move product in a materials handling system.
Fairlane Products’ extended shaft-drive rollers accommodate shaft
sizes of 3/8 to 1¼-inch shafts and come assembled with hub and set
screws to lock onto the shaft. The hub extends from one side of the roller
and is flush on the opposite side. The extended shaft-drive rollers are
available in 1½ to 4-inch diameters, with 1, 1¼ and 2-inch widths.
They come in a variety of durometers (from 20 to 95), materials (black
neoprene, white nitrile or polyurethane) and styles (solid, finned and
DuraSoft®).
Fairlane Products is a leading designer and manufacturer of rollers and
bumpers used in materials handling, assembly and manufacturing applications.
The company also designs manufactures and stocks a wide range of workholding
and positioning components, all built to promote higher productivity through
faster speeds and feeds — while their modular and economical replaceable
wear surface extends the life of expensive jigs, fixtures, jaws and clamping
mechanisms. In addition, the company designs and manufactures serrated
grippers, encompassing hardened high-speed tool steel or solid carbide
diamond pattern grippers, low-profile edge grippers, single point and
straight serration grippers.
Other products include
Swivots® — modular component workholding elements incorporating
a serrated gripper, smooth pad, or a Delrin® rest pad that rotates
and pivots for holding and positioning of irregular contour surfaces.
And Thrust Screws that allow straight-line static thrust loads without
transmitting torsional or radial forces on an object or work piece.
Send inquiries to:
Fairlane Products, Inc.,
33792 Doreka, Fraser, MI 48026.
Tel: 586.294.6100
Fax: 586.294.6822
Online: www.fairlaneproducts.com
Back
to top ^ |
 |
Product
Information—For Immediate Release
FAIRLANE PRODUCTS ADDS NEW METRIC SIZES
TO COUNTERBORE GRIPPER LINE
Fairlane Products, Inc. (Fraser, MI) has announced the addition of new
metric sizes to its line of counterbored workholding serrated grippers.
The expanded line includes metric sizes from 12mm to 24mm round and square.
The metric line complements the existing line that features sizes ranging
from ½ to 1-inch, square and round. The entire counterbore gripper
line includes grippers in various tooth patterns (coarse, fine, extra
fine). They are available in high-speed tool steel, heat treated to Rc
62. The metric counterbore grippers are part of a broad range of both
metric and inch workholding and positioning components.
Counterbored grippers are mounted utilizing a socket head cap screw from
the serrated-face side. This feature allows the versatility and options
to help eliminate the need to completely tear down the fixture to replace
the gripper—hence increased speed in fixture building and set up
time for a wide variety of workholding applications. Fairlane Products’
grippers penetrate and “grip” the workpiece for secure machining
operations. They provide holding power with minimum wear on jaws, clamp
fingers and positioning points.
Fairlane Products designs, manufactures and stocks a wide range of standard
workholding and positioning components, all built to promote higher productivity
through faster speeds and feeds. In addition, the company designs and
manufactures serrated grippers, encompassing hardened high-speed tool
steel or solid carbide diamond pattern grippers, low-profile edge grippers,
single point and straight serration grippers.
Other products include-
Swivots® — modular component workholding elements incorporating
a serrated gripper, smooth pad, or a Delrin® rest pad that rotates
and pivots for holding and positioning of irregular contour surfaces.
The company is also a leading designer and manufacturer of rollers and
bumpers used in materials handling, assembly and manufacturing applications.
Send inquiries to:
Fairlane Products, Inc.,
33792 Doreka, Fraser, MI 48026.
Tel: 586.294.6100
Fax: 586.294.6822
Online: www.fairlaneproducts.com
Back
to top ^ |
 |
|
Product
Information For Immediate Release
FAIRLANE PRODUCTS ANNOUNCES NEW METRIC AND
INCH LENGTHS AND THREAD SIZES FOR ADJUSTABLE GRIPPER LINE
Fairlane Products, Inc. (Fraser, MI) has announced the addition of new
lengths and sizes to its existing line of workholding grippers. Now available
are coarse threads from 3/8 to ¾-inch, in lengths from ½ to
3-inch and metric adjustable grippers in mid to M 20 threads in lengths
from 12 to 60mm.
High-speed tool steel, carbide-tipped adjustable grippers are available
in the full range of coarse and fine threads. Replaceable grippers are
practical and economical alternatives for many jig, fixture and chuck
jaw applications by providing flexibility and minimizing downtime during
production and set up.
Fairlane Products designs and manufactures a wide range of workholding
and positioning components, all built to promote higher productivity through
faster speeds and feeds. In addition, the company designs and manufactures
serrated grippers, encompassing hardened high-speed tool steel or solid
carbide diamond pattern grippers, low-profile edge grippers, single point
and straight serration grippers.
Other products include-
Swivots® — modular component workholding elements incorporating
a serrated gripper, smooth pad, or a Delrin® rest pad that will swivel,
tilt or pivot for holding and positioning of irregular contour surfaces.
The company is also a leading designer and manufacturer of rollers and
bumpers used in materials handling, assembly and manufacturing applications.
Send inquiries to:
Fairlane Products, Inc.,
33792 Doreka, Fraser, MI 48026.
Tel: 586.294.6100
Fax: 586.294.6822
Online: www.fairlaneproducts.com
Back
to top ^ |
 |
